Exactly How to Install a Bathtub in Your Bathroom
Exactly How to Install a Bathtub in Your Bathroom
Blog Article
Just about every person will have their own individual opinion involving How to Install a Bathtub Yourself.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a bathtub isn't precisely rocket science, however it does call for strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately difficult project. If the old tub is readily available, the job can relocate immediately; if you need to open a wall to remove the old tub and position the new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will need a helper to leave the old tub as well as set in the new one. Ensure you have qualified yourself for the job and are comfortable trying it. As opposed to employing a professional to take over a halfway-completed job, it is much better to consider employing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This short article will help you install a brand-new bath tub in your washroom if you have actually already purchased a new bathtub as well as don't need to change the setup of your previous water system pipes.
Your tools as well as material checklist should comprise the following:
Getting ready for the Installation
Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its final placement.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any kind of water staying in the system. The procedure of removing the existing taps can be quite troublesome as a result of the limited access that is typically the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto four small points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the tub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other tap.
Switch on the water supply and also examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet as well as the normal electrical outlet for leaks.
Lastly, repair the bath paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub ought to wait till the tub has been made use of at least when as this will resolve it right into its final setting.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin making certain that the washers remain in location between the faucet and also the sink. Secure the tap in position with the maker given backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap connectors. The former kind ought to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to pass through the wall surface between the bath as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to enable the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very eager about Tools You Need to Install a New Bathtub and I'm hoping you enjoyed the blog posting. Sharing is good. Helping people is fun. Thanks a lot for taking the time to read it.
Request Free Estimate Report this page